Search found 318 matches
- Mon Mar 29, 2010 7:06 pm
- Forum: Lambretta Tech
- Topic: White wire function
- Replies: 3
- Views: 1560
Re: White wire function
Its the earth
- Mon Mar 29, 2010 6:58 pm
- Forum: Lambretta Tech
- Topic: Pro-porting new Lambretta barrel
- Replies: 13
- Views: 7235
Re: Pro-porting new Lambretta barrel
Barrel looks like it's got plenty of extra meat in all the right places barrel top, transfers, gasket faces etc Looks like the secondary transfers have more area, so they will not need to be played with to much, un Like what you would have to do on a TS1. Im surprised on the std flat exhaust exit, I...
- Mon Mar 29, 2010 6:41 pm
- Forum: Lambretta Tech
- Topic: RB22 transfers - discuss
- Replies: 14
- Views: 3876
Re: RB22 transfers - discuss
Correct me if I am wrong (I barelyvisited scooterotica in January as I was out of the country), but no one has posted a photo of the silicon moulds of the RB transfer ports before on this forum. Correct? So this is the first time that many people on this fourm will have been able to visually inspec...
- Mon Mar 29, 2010 5:19 pm
- Forum: Lambretta Tech
- Topic: Areas of highest risk of piston seizing in Lambretta
- Replies: 8
- Views: 2828
Re: Areas of highest risk of piston seizing in Lambretta
Hi Enrique What you show is very good and is very common to have siezures on the stud line. Drilling holes in the piston at these point will help lubricate. But first the Rapido barrel you have with the Asso piston may need attention 1. check bore to piston clearences as some times this can be quite...
- Mon Mar 29, 2010 4:50 pm
- Forum: Lambretta Tech
- Topic: RB22 transfers - discuss
- Replies: 14
- Views: 3876
Re: RB22 transfers - discuss
Posted on here a while ago see thread
http://scooterotica.org/forum/viewtopic ... 5&start=10
Ive modded a good few now to make more symetrical
Dont forget piston
http://scooterotica.org/forum/viewtopic ... 5&start=10
Ive modded a good few now to make more symetrical
Dont forget piston
- Wed Mar 24, 2010 9:45 pm
- Forum: Lambretta Tech
- Topic: IS HE HAVING A LAUGH?
- Replies: 23
- Views: 5279
Re: IS HE HAVING A LAUGH?
eden wrote:Name and shame the seller!
I agree ....what a total bodge
- Sun Mar 14, 2010 8:36 pm
- Forum: Lambretta Tech
- Topic: Help needed on rear hub bearings
- Replies: 10
- Views: 3369
Re: Help needed on rear hub bearings
Nic PM sent
- Fri Mar 12, 2010 11:23 pm
- Forum: Lambretta Tech
- Topic: simply GREAT: "rat fink" custom lambretta
- Replies: 20
- Views: 5733
Re: simply GREAT: "rat fink" custom lambretta
sean brady scooters wrote:Dont listen to wayne mate when he says it was a pleasure to build .....cos he didnt build it..........I did ,and it was a pain in the ass......
Sean
I keep telling you shoving things up your ass wont do your Piles any good m8
- Fri Mar 12, 2010 12:23 am
- Forum: Lambretta Tech
- Topic: Help: RB25 VHSB 34mm. Side Panel cut or not
- Replies: 6
- Views: 2396
Re: Help: RB25 VHSB 34mm. Side Panel cut or not
Need to ensure opening of carb is machined down AF already do this when buying one from them And Im sure Jimmers Manifold will give more clearance
PS Stay with Delly
:smug:
PS Stay with Delly
:smug:
- Fri Mar 12, 2010 12:18 am
- Forum: Lambretta Tech
- Topic: E G T / cylinder head temp readings
- Replies: 22
- Views: 6696
Re: E G T / cylinder head temp readings
I too querie some of these cheaper EGT For one the cabling from probe to gauge should be of the correct type cable for the type of thermocouple being used by the gauge. For example a typical proper K type TC should have a colour cable of Green White using IEC 584-3 standards white being -ve and the ...