Search found 1030 matches

by HxPaul
Wed Apr 24, 2019 7:29 pm
Forum: Lambretta Tech
Topic: Quatrini 210 and chisel speed exhaust
Replies: 6
Views: 232

Re: Quatrini 210 and chisel speed exhaust

Shouldn't the exhaust fit at the other side of the bracket.
by HxPaul
Fri Apr 19, 2019 8:23 am
Forum: Lambretta Tech
Topic: 24mm Jetex alternatives
Replies: 7
Views: 303

Re: 24mm Jetex alternatives

I have a 25 mil jetex that I use on my series 1(I have three scooters and the other two have PHBL 25 carbs)The series 1 has a Casa 185 kit and an AF clubman.I run that through an undrilled airbox with the baffle removed and an ordinary air filter element,it uses a 130 main jet,a 48 pilot jet and is ...
by HxPaul
Fri Apr 12, 2019 5:44 pm
Forum: General Scooter Chat
Topic: PHBL Needles
Replies: 3
Views: 165

Re: PHBL Needles

I have presumed that a D28 needle would be leaner than a D30 needle. Is it that straight forward? I only ask as the D30 needle that i have in the bike is very tapered, virtually to a point, and a D28 needle that i brought from SIP hardly tapers at all. Can someone advise or point me to some technic...
by HxPaul
Tue Apr 09, 2019 8:30 am
Forum: Lambretta Tech
Topic: Troubleshooting inboard semi-hydrolic
Replies: 5
Views: 208

Re: Troubleshooting inboard semi-hydrolic

Tv175 original break and steel disk. I bought a new semi hydraulic back plate. Reservoir is behind the horn cast. I have a bleeding kit and pretty confident it's good. Took anti rattle clip off. Holes in disk are 13/32. Copper grease on the 3 pegs. New oil seal for the speedo area. I cleaned the di...
by HxPaul
Thu Apr 04, 2019 8:04 am
Forum: Lambretta Tech
Topic: Inboard disc
Replies: 5
Views: 454

Re: Inboard disc

I'm using a ScootRS inboard disc,cable operated with a reverse pull set up.Unfortunately you cant buy them new as they've stopped trading.
by HxPaul
Thu Mar 21, 2019 8:50 am
Forum: Lambretta Tech
Topic: cable operated front disc poor performance
Replies: 6
Views: 609

Re: cable operated front disc poor performance

Hi,chaps a mate has just bought a tv175 with a repro front disc, cable operated, in reverse pull style.with everything properly adjusted the brake lever is hitting the grips before any braking happens,we have put new pads in etc. the actuator seems a very sloppy fit in the backplate,and the actuato...
by HxPaul
Thu Mar 21, 2019 8:41 am
Forum: Lambretta Tech
Topic: 5 min removal of bearing race from crankshaft
Replies: 10
Views: 639

Re: 5 min removal of bearing race from crankshaft

hendy wrote:
Wed Mar 20, 2019 10:26 pm
I use this. Means I can use it for a load of other jobs besides.

https://rover.ebay.com/rover/0/0/0?mpre ... 2727795959
I've got this tool and tried 3 times to get mag bearing track off,without success,in the end I had to resort to grinding it off.
by HxPaul
Sat Feb 23, 2019 9:06 am
Forum: Lambretta Tech
Topic: Series 1 Wiring /elecrtonic ignition
Replies: 3
Views: 257

Re: Series 1 Wiring /elecrtonic ignition

Iseries 1 loom with 2 joint green wires into 1 connector , 1 purple and 1 brown 1 separate green in thick sleeve (probably an earth?) (pink and black rear light) What goes where with regards to the regulator? All wires from stator sorted out ok to CDI. No ignition but has cut out button. Or best to...
by HxPaul
Wed Feb 13, 2019 4:35 pm
Forum: Lambretta Tech
Topic: LT coils
Replies: 8
Views: 569

Re: LT coils

by HxPaul
Thu Jan 10, 2019 5:44 pm
Forum: Lambretta Tech
Topic: Mag flange all the same?
Replies: 22
Views: 1393

Re: Mag flange all the same?

I thought you had to be a member to post on this site.