Search found 11 matches

by petemaisey
Mon Apr 11, 2011 6:48 pm
Forum: Lambretta Tech
Topic: Legshield glovebox mounting
Replies: 3
Views: 1552

Re: Legshield glovebox mounting

My method was to fix the top in a similar fashion to a toolbox top fitting. A small keyhole shape upsidedown slot in the legshield centre. Put a hex bolt head first into the slot, tighten a washer and nut onto it to hold. An "L" bracket fixed inside the legshield tool box to line up with t...
by petemaisey
Wed Feb 09, 2011 7:35 pm
Forum: Lambretta Tech
Topic: Electronic seat - Ebay
Replies: 10
Views: 3130

Re: Electronic seat - Ebay

I don@t see any waffle panel. It may also be just the cover. :|

Pete
by petemaisey
Mon Sep 06, 2010 7:50 pm
Forum: Lambretta Tech
Topic: GP CRANK/ S1 MAG HOUSING
Replies: 8
Views: 2681

Re: GP CRANK/ S1 MAG HOUSING

Yeah, I know what you mean. :?
I left mine out in the sun and it went off.

Pete ;)
by petemaisey
Mon Sep 06, 2010 6:09 pm
Forum: Lambretta Tech
Topic: GP CRANK/ S1 MAG HOUSING
Replies: 8
Views: 2681

Re: GP CRANK/ S1 MAG HOUSING

You should get the backplate tomorrow. :)
You will need a flywheel housing, 2205 bearing, inner and outer oil seal and a circlip.

Pete
by petemaisey
Mon Sep 06, 2010 5:44 pm
Forum: Lambretta Tech
Topic: GP CRANK/ S1 MAG HOUSING
Replies: 8
Views: 2681

Re: GP CRANK/ S1 MAG HOUSING

A late type S1 mag housing will be ok. Early ones with petroil lubricated flywheel bearing will be no good, (it is easy to identify early type, the flywheel bearing and rollers stay on the crank when you take the flywheel housing off). The late type housing has a circlip holding in the oil seal. If ...
by petemaisey
Thu Aug 12, 2010 1:11 pm
Forum: Lambretta Tech
Topic: Problems fitting an electronic indian ignition on series 1
Replies: 3
Views: 1358

Re: Problems fitting an electronic indian ignition on series

Hi Jaime, two things to check.
The li boss may be too tight inside the new stator.
Some times the flywheel rubs on the stator plate, (3x 10mm head) bolts.

Pete
by petemaisey
Tue Aug 03, 2010 9:55 pm
Forum: Lambretta Tech
Topic: AF Electronic Stator Kaput after only 12hrs
Replies: 4
Views: 1445

Re: AF Electronic Stator Kaput after only 12hrs

It could be a "dry" solder joint. On the earth tag perhaps.

Pete
by petemaisey
Tue Aug 04, 2009 6:49 pm
Forum: Lambretta Tech
Topic: Can this be repaired? ***pictures****
Replies: 9
Views: 2542

Re: Can this be repaired? ***pictures****

I have in the past reduced and re-formed a set of Italian SIII legshields. I had to make a tool to form the beading channel. Other than that there are some badge holes to fill.
Pete
by petemaisey
Sat May 16, 2009 2:29 pm
Forum: Lambretta Tech
Topic: what mag housing....
Replies: 2
Views: 1545

Re: what mag housing....

Either will fit. The Spanish one would be favourite as the transfer detail should be more of a match.
Make sure your barrell does not bottom out onto the mag house.
Pete
by petemaisey
Fri May 08, 2009 5:45 pm
Forum: Lambretta Tech
Topic: Original GP 200 Rear light unit & lens
Replies: 7
Views: 2435

Re: Original GP 200 Rear light unit & lens

There is a small semi circular cut out at the bottom which allows water to escape. Rainwater can get behind the tail light through the hole in the frame that the loom passes through. Also shown is the large rubber grommet and sleeve nut that holds the assembly. The holes in the frame were made large...

cron