Search found 689 matches

by kevspeed
Sat Jun 20, 2020 9:52 am
Forum: Wanted
Topic: Twin tank
Replies: 2
Views: 355

Re: Twin tank

nick b wrote:
Thu May 21, 2020 3:15 pm
lambretta locomociones in spain were selling on last time i looked
8-) Thanks,ill have a look there.
by kevspeed
Sat Jun 20, 2020 9:50 am
Forum: Lambretta Tech
Topic: Piston circlips.....
Replies: 4
Views: 388

Re: Piston circlips.....

gaz_powell wrote:
Thu Jun 18, 2020 8:30 pm
Vertex are usually wire type either the G or looped ends
It looks very much like it,having compared the grooves to a piston fitted with the flat 'Seeger' type clips 8-)
by kevspeed
Sat Jun 20, 2020 9:48 am
Forum: Lambretta Tech
Topic: Piston circlips.....
Replies: 4
Views: 388

Re: Piston circlips.....

I do not know what sort should apply, but in any case, use a magnifying glass or needle to 'feel' the groove profile. If they are to suit a 16 mm wrist pin, I probably have spares of either type you can have. But do please check first :D Thanks for that,i had a poke around and luckily had an old Bo...
by kevspeed
Thu Jun 18, 2020 4:24 pm
Forum: Lambretta Tech
Topic: Piston circlips.....
Replies: 4
Views: 388

Piston circlips.....

Hi all,just a quick question. I have misplaced the piston circlips for my 57.8 Vertex piston,they have fallen out of the box at sometime over the past 5 years,so im a bit stuck as i dont know if they were the usual 'Seeger',flat type circlips,or the wire type :( :( ,anybody know which replacements i...
by kevspeed
Sun Jun 14, 2020 9:02 pm
Forum: Lambretta Tech
Topic: Bitubo rear shock
Replies: 2
Views: 279

Re: Bitubo rear shock

👍
by kevspeed
Sun Jun 14, 2020 8:06 pm
Forum: Lambretta Tech
Topic: Bitubo rear shock
Replies: 2
Views: 279

Bitubo rear shock

Hi all, any recommendations for someone to service/re seal my Bitubo rear shock absorber.
I've had it since the 80's and would like to use it on my 1980's cutdown I'm throwing together, thanks in advance.... Kev
by kevspeed
Sun Jun 07, 2020 1:16 am
Forum: Lambretta Tech
Topic: Advice please
Replies: 11
Views: 1002

Re: Advice please

Atomiser too big, Warkton Tornado had the answer straight off.
by kevspeed
Thu Jun 04, 2020 2:25 pm
Forum: Lambretta Tech
Topic: Suzuki 190
Replies: 17
Views: 1166

Re: Suzuki 190

I’ve done one of those aS well on one if the latest SIL stage 4 barrels. 3 stud holes to 14mm and one near the manifold to 13mm. Use a 200 head and drill out that as well. I messy job but it work’s okay doesn’t feel right pushing it over the studs etc Did a few of these,but they 'clattered' a bit.N...
by kevspeed
Sun May 24, 2020 12:49 pm
Forum: Sports Bar
Topic: The Song Title Thread - Pointless but Addictive!
Replies: 23208
Views: 1286240

Re: The Song Title Thread - Pointless but Addictive!

Always the sun...........The Stranglers
by kevspeed
Fri May 22, 2020 6:20 am
Forum: Lambretta Tech
Topic: Suzuki 190
Replies: 17
Views: 1166

Re: Suzuki 190

I've had a TV cylinder bored to take a 66mm piston, the walls were a bit thin, but I ran it in very carefully and all was well.
The maximum I've had a 150 cylinder out to was 64mm with the Suzuki piston, again all good.