Search found 50 matches
- Mon Aug 28, 2017 7:01 am
- Forum: Lambretta Tech
- Topic: Gearbox rebuild,
- Replies: 3
- Views: 2033
Gearbox rebuild,
I have recently rebuilt my gearbox series 3 GP, I followed sticky's book for assistance. The confusion lies in the order the gears are placed, the book says 4th flat side down with boss side up toward endplate. And the 3rd & 2nd boss side up until 1st. Other sources say fourth flat side down bos...
- Tue Sep 27, 2016 9:57 am
- Forum: Lambretta Tech
- Topic: BGM LED light for GP
- Replies: 5
- Views: 2657
Re: BGM LED light for GP
I had to remove the reflector and then file down the tops of the dish to create two flat surface, I used a silicone sealant to fix it. Sealants allow vibration better than glueing it.
Sent from my SM-G900F using Tapatalk
Sent from my SM-G900F using Tapatalk
- Tue Sep 27, 2016 9:57 am
- Forum: Lambretta Tech
- Topic: BGM LED light for GP
- Replies: 5
- Views: 2657
Re: BGM LED light for GP
I had to remove the reflector and then file down the tops of the dish to create two flat surface, I used a silicone sealant to fix it. Sealants allow vibration better than glueing it.
Sent from my SM-G900F using Tapatalk
Sent from my SM-G900F using Tapatalk
- Fri May 13, 2016 10:35 pm
- Forum: Lambretta Tech
- Topic: Drive side Bearing query
- Replies: 5
- Views: 2736
Re: Drive side Bearing query
Thanks for that, it was because I ordered from bearing, don't know if by mistake koyo 2rs ecp, they are steel inserts with rubber lip. I pulled one side, and didn't know if ecp would work. I know the lip is not substitute just an addition to the main seal.
Sent from my SM-G900F using Tapatalk
Sent from my SM-G900F using Tapatalk
- Thu May 12, 2016 10:13 am
- Forum: Lambretta Tech
- Topic: Drive side Bearing query
- Replies: 5
- Views: 2736
Drive side Bearing query
I have a question about bearings particular the drive side, The required one is the 6305 c3 using good name brands like FAG, SKF, Koyo etc. There is various sites saying that a 6305 2rs can be used, with just removing one seal on one side. This gives a extra seal in addition to the drive side plate ...
- Sun Nov 08, 2015 8:13 am
- Forum: Lambretta Tech
- Topic: Leak testing
- Replies: 26
- Views: 8925
Re: Leak testing
Hi, if you ensure that either inlet or exhaust plus spark plug is sealed and then apply an over pressure, that pressure value should stay, not then indicating a leak, soapy water to find the leak, if then not found, remove the flywheel to soapy water test the flywheel seal a process of elimination. ...
- Mon Aug 24, 2015 12:03 am
- Forum: Lambretta Tech
- Topic: Basic Carb set up question on 26mm Mikuni
- Replies: 11
- Views: 5021
Re: Basic Carb set up question on 26mm Mikuni
Live in sunny Wellington, will check your advice out, thanks
- Sun Aug 23, 2015 9:01 pm
- Forum: Lambretta Tech
- Topic: Basic Carb set up question on 26mm Mikuni
- Replies: 11
- Views: 5021
Re: Basic Carb set up question on 26mm Mikuni
Thanks Yamlam, I think I will have to Google and just get a wide range of jets and go slowly,
the joys of living on the other side of the planet.
the joys of living on the other side of the planet.
- Sun Aug 23, 2015 12:43 pm
- Forum: Lambretta Tech
- Topic: Basic Carb set up question on 26mm Mikuni
- Replies: 11
- Views: 5021
Re: Basic Carb set up question on 26mm Mikuni
After further Googling, i found that an outer diameter on the spigot side of 33mm and a outer diameter of the inlet side of 44mm, it is a VM28 model in the TM flat series. Hence your confusion. Thank you for helping me clear this up. Does anyone have some basic jetting sizes for it? As the sizes men...
- Sat Aug 22, 2015 11:06 am
- Forum: Lambretta Tech
- Topic: Basic Carb set up question on 26mm Mikuni
- Replies: 11
- Views: 5021
Re: Basic Carb set up question on 26mm Mikuni
Hi Yamlam got the old digital gauge out, 33mm for the outer diameter on the spigot side of the carb, with a 25.98mm inner diameter..does this make any more sense?