Search found 17 matches

by Gazjet1
Sat Dec 07, 2019 7:35 pm
Forum: Lambretta Tech
Topic: Motoplat ignition coil
Replies: 13
Views: 952

Re: Motoplat ignition coil

Also got a couple if Carlos can’t find his
by Gazjet1
Tue Dec 03, 2019 9:47 pm
Forum: Lambretta Tech
Topic: Motoplat ignition coil
Replies: 13
Views: 952

Re: Motoplat ignition coil

Is it the electronic one or points one you need?
by Gazjet1
Mon Dec 02, 2019 9:48 pm
Forum: For Sale
Topic: Cyclone 5 speed gearbox
Replies: 0
Views: 597

Cyclone 5 speed gearbox

Cyclone 5 speed gearbox (V1), only done around 200 miles, includes all five loose cogs, selector and cluster (this has been upgraded by Replay Scooters to compensate for original design fault with the case hardening on the bearing track). £350 plus p&p.
PM for more info or images
by Gazjet1
Mon Dec 02, 2019 7:07 am
Forum: For Sale
Topic: MB 5 plate clutch
Replies: 0
Views: 345

MB 5 plate clutch

Complete MB five plate clutch ( 5x Surflex ‘B’ friction plates) 46 tooth MB rear sprocket, clutch basket, springs and pressure plate, excellent condition & very low mileage - £200 plus p&p.
PM for further info, images etc
by Gazjet1
Thu Dec 20, 2018 8:32 pm
Forum: Lambretta Tech
Topic: Scomadi forks
Replies: 4
Views: 1094

Re: Scomadi forks

Unfortunately don’t have the old set to try, am fairly confident frame is fine, had it jigged prior to paint?
Will have another go this weekend
by Gazjet1
Tue Dec 18, 2018 8:14 pm
Forum: Lambretta Tech
Topic: Scomadi forks
Replies: 4
Views: 1094

Re: Scomadi forks

Sorry, yeah PM forks, have fitted loads before with the very little issue, but these will just not push all the way through the steering tube? We’re yours series one’s
by Gazjet1
Sun Dec 16, 2018 10:16 pm
Forum: Lambretta Tech
Topic: Scomadi forks
Replies: 4
Views: 1094

Scomadi forks

Just got round to fitting a set of Scomadi forks into a series one, they are the correct ones, as in the stem length & pinch bolt slot is at the rear rather than the side. However they will not slide fully through the steering column, and seem to stick approx. two inches short. Just wondered if anyo...
by Gazjet1
Sat Oct 31, 2015 10:11 pm
Forum: Lambretta Tech
Topic: Is there a correct sequence.....?
Replies: 7
Views: 1726

Re: Is there a correct sequence.....?

Just checked old 'official manual' it says- off side, then near side then anchor bolt/nut.
by Gazjet1
Sat Oct 31, 2015 9:58 pm
Forum: Lambretta Tech
Topic: Is there a correct sequence.....?
Replies: 7
Views: 1726

Re: Is there a correct sequence.....?

I also seem to remember reading in one of the older manuals there is a sequence, could be well wrong but seem to recall it was, near side first then the anchor bolt then the off side spindle nut.
Am now off to double check, not sure if/how much difference it actually makes though!
by Gazjet1
Sat Apr 25, 2015 6:48 pm
Forum: Lambretta Tech
Topic: Scootrs ignition switch
Replies: 1
Views: 614

Scootrs ignition switch

Hi, anybody got a copy of a wiring diagram to wire in a Scootrs ignition switch? Thanks in advance