Search found 226 matches

by B-Race Tuning
Mon Apr 22, 2019 9:17 pm
Forum: General Scooter Chat
Topic: CornwallScooterCentre Break-in
Replies: 13
Views: 1640

Re: CornwallScooterCentre Break-in

I've contacted Graeme and hopefully he'll be along dreckly to give full details. Yes, it's been a bad weekend Mark. It'll only take a small lead to get some sort of result.
by B-Race Tuning
Mon Apr 22, 2019 7:54 pm
Forum: General Scooter Chat
Topic: CornwallScooterCentre Break-in
Replies: 13
Views: 1640

CornwallScooterCentre Break-in

I've been made aware of Graeme's workshop having been broken into,Customers' Scoots and cash gone. I don't have details/ photos so am unable to give description's. Hopefully some with more info will be along dreckly. But (and not necessarily just here in South-West), keep your ears to the ground/ ey...
by B-Race Tuning
Sun Jan 06, 2019 6:54 pm
Forum: General Scooter Chat
Topic: how do i tell the difference
Replies: 4
Views: 774

Re: how do i tell the difference

The obvious and visible immediately is the thickness (diameter) of the handlebars where the gearchange and switch housing meet it. Indian thicker by ?5mm?, The gearchange and switch housing are correspondently different. If not familiar you'd need the two different types side by side. Someone will b...
by B-Race Tuning
Thu Dec 20, 2018 10:28 pm
Forum: Tech FAQ
Topic: Lambretta Rear Brake Adjuster
Replies: 14
Views: 1659

Re: Lambretta Rear Brake Adjuster

Boom, Dude ;-)
by B-Race Tuning
Thu Dec 20, 2018 10:27 pm
Forum: Tech FAQ
Topic: Lambretta Rear Brake Adjuster
Replies: 14
Views: 1659

Re: Lambretta Rear Brake Adjuster

ALL it does is stop the knurled knob un-adjusting by keeping the barrell part (that sits in the arm) pushing under pressure against the curved recess in the adjuster (knurled knob). In theory (and someone must have practical experience of it), without it, as you release the brake the adjuster could ...
by B-Race Tuning
Sun Dec 09, 2018 8:23 pm
Forum: Lambretta Tech
Topic: Pickup /flywheel alignment madness
Replies: 10
Views: 1284

Re: Pickup /flywheel alignment madness

great 17 is is then, Thanks for your advice guys and the image is very helpful too. If I spin my flywheel with a drill and socket adaptor I should be able to time the ignition without the need to start and run the engine. I read on MB about a neat mod using a tank strap trunnion to make an adjustab...
by B-Race Tuning
Mon Dec 03, 2018 9:40 pm
Forum: Lambretta Tech
Topic: Replacement seal for Taff hydraulic slave cylinder?
Replies: 13
Views: 1221

Re: Replacement seal for Taff hydraulic slave cylinder?

Adam, the more common one is a Metro seal. (Several early ones were Mini). S
by B-Race Tuning
Sun Sep 23, 2018 8:37 pm
Forum: Lambretta Tech
Topic: Chain tension and scootopia chain
Replies: 3
Views: 891

Re: Chain tension and scootopia chain

Hi Fluff, besides your new chain, are either the front sprocket or crownwheel new? Or from the original/ a different engine? There are some awful versions of both out there, either slightly over/ undersized and I've seen both sprockets and crown wheels machined off centre (eccentric). Your original/...
by B-Race Tuning
Mon Aug 20, 2018 11:16 am
Forum: Lambretta Tech
Topic: Cowboy cylinder porting
Replies: 11
Views: 1400

Re: Cowboy cylinder porting

I can see those photos, yes it does look a little thin for your casings doesn't it. The "artificial" support does work. If you take that further, (other than using a longer rodded crank[costly]), It is possible to get a machine shop to take the gasket face at the base as far up the cylinder as the f...
by B-Race Tuning
Fri Aug 17, 2018 3:51 pm
Forum: Lambretta Tech
Topic: Cowboy cylinder porting
Replies: 11
Views: 1400

Re: Cowboy cylinder porting

Johnny, be aware the cylinder may have come from/ was matched to, for example, a Spanish casing with tons of meat around the crankcase mouth to suit said "over" porting, or even set up with a 110/115/116 rod. Utilising a packing plate (even a 3mm for 110 rod) the cylinder transfer ports at the base ...