I said " aye, the f@@king sinks blocked again "
Search found 59 matches
- Sat Jul 09, 2016 8:27 pm
- Forum: Sports Bar
- Topic: Stupid Jokes
- Replies: 253
- Views: 112795
Re: Stupid Jokes
My wife came into the lounge in her nightie and said, "darling, i've just shaved my fanny so you know what that means mmmmmmm,
I said " aye, the f@@king sinks blocked again "
I said " aye, the f@@king sinks blocked again "
- Sun Jul 03, 2016 5:36 pm
- Forum: Lambretta Tech
- Topic: Distance between headset and toolbox
- Replies: 2
- Views: 1590
Re: Distance between headset and toolbox
Reading more into it it says dimension is from top of legshield and the recess in the bodywork above the toolbox aperture, (under the seat nose with the toolbox door open )
- Sun Jul 03, 2016 5:32 pm
- Forum: Lambretta Tech
- Topic: Distance between headset and toolbox
- Replies: 2
- Views: 1590
Re: Distance between headset and toolbox
Right mate, by coincidence I got an original workshop manual amongst a few bits I bought which has a dimension that could be what you need. It shows arrow from what looks like the bottom of the headset under ignition /cut out and going to the top of the toolbox door with a size of 17" for the L...
- Wed Apr 27, 2016 4:16 pm
- Forum: General Scooter Chat
- Topic: Scooter couriers
- Replies: 1
- Views: 1390
Re: Scooter couriers
Ring Graham on 07780 671438, picks up and delivers all over the UK
- Wed Feb 03, 2016 8:24 pm
- Forum: Scooter Insurance
- Topic: isurance advice
- Replies: 8
- Views: 13634
Re: isurance advice
Did you get my PM about insurance ?
Cheers
Cheers
- Thu Aug 27, 2015 6:15 pm
- Forum: Lambretta Tech
- Topic: nickel plating
- Replies: 15
- Views: 6662
Re: nickel plating
I'll have it when you throw it away 
- Mon Jun 22, 2015 11:10 pm
- Forum: General Scooter Chat
- Topic: Ebay getting excited again...
- Replies: 8
- Views: 3449
Re: Ebay getting excited again...
You tell me. If I'm being cynical then please say, but it only takes a shrewd fella to get some far eastern foundry to cast a few pairs off from an original set, chuck a pair of these on..http://2ndavenuescooters.com/?p=4191 & Robert's your Dad's bruvver. :twisted: Dead easy to copy, provenance...
- Wed May 13, 2015 3:36 pm
- Forum: General Scooter Chat
- Topic: Halcyon Bar End Mirrors
- Replies: 6
- Views: 4050
Re: Halcyon Bar End Mirrors
That'll be me then 
- Wed May 06, 2015 11:30 am
- Forum: General Scooter Chat
- Topic: Indian Bodge job
- Replies: 7
- Views: 3727
Re: Indian Bodge job
Old Indian GP150 casing. They've obviously re-used some old short engine mounts. But to make them fit tight, have used cut up bits of tin can to wedge in Good bodge !! http://i230.photobucket.com/albums/ee222/st0kky/mnts.jpg Ha ha reminds me of an Indian mate of mine bought a Sherpa van off a Gipsy...
- Fri May 01, 2015 6:03 pm
- Forum: Lambretta Tech
- Topic: What are the cylinder stud spacing dimensions?
- Replies: 6
- Views: 2477
Re: What are the cylinder stud spacing dimensions?
You are looking for the 90 mm gasket face.
Got me confused here,i'm assuming he wants to know the PCD of the studs, what has the gasket face got to do with it ?
Got me confused here,i'm assuming he wants to know the PCD of the studs, what has the gasket face got to do with it ?