Search found 32 matches
- Sat Apr 15, 2017 1:01 pm
- Forum: General Scooter Chat
- Topic: Remade Side Panels
- Replies: 31
- Views: 10746
Re: Remade Side Panels
I ordered and received a pair of LIS panels from Scootrs about four years ago and they were fine, definitely machine pressed, for £44 each!!, I don't know this for a fact but knowing how much tooling cost there is probably only one manufacturer of replacement panels, and they are probably in vietnam...
- Sun Jan 29, 2017 8:44 pm
- Forum: Vespa Tech
- Topic: Increase carb size on 177 kit
- Replies: 5
- Views: 4303
Re: Increase carb size on 177 kit
I've got a 24/24 on a two port Pinasco 177, done over 1000 miles, its got standard P200 jetting but is a bit rich, plenty of smoke on startup. Ive just drilled out holes to the heart shape in air filter and not ridden since so hopefully it'll weaken it be better now.
- Sun Jan 29, 2017 8:36 pm
- Forum: General Scooter Chat
- Topic: Scootopia Vespa Big Bore vs Sito and Sip 2.0. Exhausts
- Replies: 14
- Views: 9420
Re: Scootopia Vespa Big Bore vs Sito and Sip 2.0. Exhausts
Ive done about 1000 miles on a Pinasco 172 with the scootopia exhaust, no problems at all, goes well, it definitely needs one of the springs supplied fitted incase it slips off cylinder which mind did after fitting, tight on now but its just incase.
- Tue Feb 09, 2016 1:42 am
- Forum: Vespa Tech
- Topic: Vespa GT125 2 port clutch gear upgrade
- Replies: 0
- Views: 938
Vespa GT125 2 port clutch gear upgrade
Hi im restoring a Vespa 67 GT125, planning on putting a cast Pinasco 177 kit on, however i understand the clutch cog can be changed to alter the gearing, SIP do several different sizes and I can't find the most suitable size to use, many people must have done it but can't find anything on web, can a...
- Sat Aug 01, 2015 12:49 am
- Forum: Lambretta Tech
- Topic: Scootopia SH2/22
- Replies: 4
- Views: 2825
Re: Scootopia SH2/22
I have one fitted from the first batch, much better quality than a jetex which isn't surprising, does what it says on the tin runs fine and looks and acts like a SH2/22
- Fri May 29, 2015 10:12 pm
- Forum: Lambretta Tech
- Topic: What are the pros and cons of cast iron vs. aluminium barrel
- Replies: 50
- Views: 20513
Re: What are the pros and cons of cast iron vs. aluminium ba
Going back to original post, I have a Gori sport 200 kit fitted, ive done a few thousand miles on it, good for 60mph + i run through airbox with a 22mm carb. As mentioned i like the idea that you get warned by an iron cylinder before it heat seizes, it nipped up on way back from Tenby after thrashin...
- Sun Jun 29, 2014 11:31 pm
- Forum: Carburettor Set-ups
- Topic: Mugello 198, Delly 25mm, ScootRs pipe - jetting?
- Replies: 5
- Views: 4106
Re: Mugello 198, Delly 25mm, ScootRs pipe - jetting?
I had a very similar setup, only difference was a 264 atomiser and a 100 main, id up main jet to 105 and see if this cures it
- Wed May 28, 2014 9:38 pm
- Forum: Lambretta Tech
- Topic: 25mm Dellorto set up....grrrrr :(
- Replies: 17
- Views: 12256
Re: 25mm Dellorto set up....grrrrr :(
I've got the same setup, but have had to go down to a 40 pilot jet to get it set up right and also start when warm, gave up on the drilled air box in the end and went to a remote filter, didn't make loads of difference though, D22, 264, second clip from top, 60 choke, 100 main.
- Thu May 01, 2014 6:19 pm
- Forum: Vespa Tech
- Topic: help, scoot chugging, back firing
- Replies: 13
- Views: 4841
Re: help, scoot chugging, back firing
I had exactly the same symptoms, it was the pickup
- Fri Apr 11, 2014 8:47 pm
- Forum: Lambretta Tech
- Topic: Scootopia mounts.
- Replies: 37
- Views: 17366
Re: Scootopia mounts.
I had my mounts replaced at scootopia recently, i have noticed a bitmore vibration which i would expect. My old mounts were soft as marshmallow and realy worn, great for soaking up vibrations but not good when cornering