Search found 42 matches
- Fri Jan 18, 2013 3:58 pm
- Forum: Lambretta Tech
- Topic: Correct oil mix percentage 3% ?
- Replies: 15
- Views: 4993
Re: Correct oil mix percentage 3% ?
Modern oils a lot better, 3% or 4% if it means you worry less
- Sun Oct 14, 2012 7:44 pm
- Forum: Lambretta Tech
- Topic: Should my Lammy sound like this....
- Replies: 10
- Views: 3272
Re: Should my Lammy sound like this....
Loose baffles?
- Wed Sep 12, 2012 8:27 am
- Forum: Lambretta Tech
- Topic: Shortest PHBH Carb Manifold?
- Replies: 11
- Views: 4652
Re: Shortest PHBH Carb Manifold?
Just for reference I had the Mugello manifold machined down for £20 at a local engineering firm, chap turned it around in a day for me. I had to lengthen and tweak the fuel tap rod to go behind the carb but I've now got a breath sweet filter that is not crushed by the side panel and I'm much happie...
- Thu Sep 06, 2012 9:26 pm
- Forum: Lambretta Tech
- Topic: very loud noise from engine
- Replies: 5
- Views: 1732
Re: very loud noise from engine
I've started texting my neighbours just before 7am to wake them up politely before I start the fecker up
- Sun Sep 02, 2012 5:38 pm
- Forum: Lambretta Tech
- Topic: Mugello 186 piston shims
- Replies: 6
- Views: 2112
Re: Mugello 186 piston shims
Might be worth buying a wider small end bearing assuming your crank is shimmed, Cambridge lambretta have them in stock I think
- Sun Sep 02, 2012 3:18 am
- Forum: Lambretta Tech
- Topic: Shortest PHBH Carb Manifold?
- Replies: 11
- Views: 4652
Re: Shortest PHBH Carb Manifold?
Thanks for all the advice guys :-) I did think about having my mugello manifold machined down but I don't want to be without the use of the lammy for a few days, my mate who does little jobs like that for me is great but can't be rushed! I'm going to give the mb or Readspeed manifold a try I think.....
- Sat Sep 01, 2012 9:27 pm
- Forum: Lambretta Tech
- Topic: muggy carb help
- Replies: 5
- Views: 2143
Re: muggy carb help
Hello, I can only help by telling you what I'm using with the same carb and V4 mugello 200 cylinder, I've used an Ancilloti exhaust but now have a Gori and forget my earlier settings, shouldn't be two far off though :-) I think your slide may be a bit lean to compensate for an over rich atomiser and...
- Fri Aug 31, 2012 11:16 pm
- Forum: Lambretta Tech
- Topic: Shortest PHBH Carb Manifold?
- Replies: 11
- Views: 4652
Shortest PHBH Carb Manifold?
Any suggestions as to the shortest reach PHBH Carb manifold for a piston port engine? I've used the Mugello manifold on my last two engines and am looking for something as short as possible to give me more carb/pannel clearence for the filter, the MB downdraft one is an obvious choice and looks to g...
- Tue Aug 14, 2012 6:38 pm
- Forum: Lambretta Tech
- Topic: MB Clubman - News
- Replies: 34
- Views: 10588
Re: MB Clubman - News
Summer?
- Thu Aug 09, 2012 10:22 pm
- Forum: Lambretta Tech
- Topic: MB Race Tour cylinder kit opinions
- Replies: 62
- Views: 27050
Re: MB Race Tour cylinder kit opinions
I'll consider myself lucky.....
Are you expecting to bolt a on a new kit and its inlet, exhaust and transfers to match perfectly with your manifold, exhaust and engine case?
Good luck to you
I'll add that the kits you mention above are both great IMHO
Are you expecting to bolt a on a new kit and its inlet, exhaust and transfers to match perfectly with your manifold, exhaust and engine case?
Good luck to you
I'll add that the kits you mention above are both great IMHO