Search found 655 matches

by Minority
Sun Jun 30, 2019 3:36 am
Forum: Lambretta Tech
Topic: Avanti Upgrade
Replies: 13
Views: 938

Re: Avanti Upgrade

I fitted one of Ron's 70mm Mitaka pistons to my Rapido. When I fitted a reed valve to the Rapido I cut the hole and skirt the same as his TS1 version and it was fine. The ring pegs also allowed me to cut a boost port.
by Minority
Fri May 24, 2019 5:20 am
Forum: Lambretta Tech
Topic: Finally have the LiS 185cc running ok
Replies: 8
Views: 803

Re: Finally have the LiS 185cc running ok

Glad you are out and about now and I hate to be the bearer of bad tidings, but I've jut stripped down a 225 version after about 450 miles and it had a ring gap of 1.3mm! It looks to be a combination of ring and bore wear so you may have to keep a check on yours.
by Minority
Sat Apr 06, 2019 2:44 am
Forum: Lambretta Tech
Topic: BGM or ??
Replies: 9
Views: 1262

Re: BGM or ??

nellyboyo wrote:
Fri Apr 05, 2019 5:46 pm
Well , update on this ...only done 30 miles on the Ron moss pipe . Great fit , not too loud , tons of grunt , can’t wait to open it up a bit . Great service from Ron by the way


Sent from my iPhone using Tapatalk
Always top service from Ron in my experience!
by Minority
Mon Mar 25, 2019 4:24 pm
Forum: General Scooter Chat
Topic: SIP Speedo set up.
Replies: 9
Views: 964

Re: SIP Speedo set up.

Got to disagree, the revs setting has bugger all to do with the speed setting. You have to tell the speedo you are using the external sensor rather the cable (referred to as internal from memory) then you have to tell it how many pulses per wheel revolution ( if you have one magnet I expect it shou...
by Minority
Mon Mar 25, 2019 11:13 am
Forum: General Scooter Chat
Topic: SIP Speedo set up.
Replies: 9
Views: 964

Re: SIP Speedo set up.

Got to disagree, the revs setting has bugger all to do with the speed setting. You have to tell the speedo you are using the external sensor rather the cable (referred to as internal from memory) then you have to tell it how many pulses per wheel revolution ( if you have one magnet I expect it shoul...
by Minority
Sun Dec 30, 2018 6:02 am
Forum: Tech FAQ
Topic: Lambretta Rear Brake Adjuster
Replies: 14
Views: 1677

Re: Lambretta Rear Brake Adjuster

hat wrote:
Sat Dec 22, 2018 4:38 pm
I’d switch to the cable with the built in threaded section and do away with this adjuster. One less thing to worry about
I agree with you about the new inner cable with threaded end, but you still need the spring in theory to keep tension on the adjuster nut ;)
by Minority
Thu Nov 01, 2018 3:08 am
Forum: General Scooter Chat
Topic: Uni Lambretta 200 casing
Replies: 40
Views: 9823

Re: Uni Lambretta 200 casing

We've had a few delivered to Perth, Western Australia, so they must be available now. On initial perusal they look good quality, like the side casings and mag housings, and I think they have a bigger gasket face around the transfers. I wonder of they are being shipped directly from UNI? They look g...
by Minority
Tue Oct 30, 2018 4:05 am
Forum: General Scooter Chat
Topic: Uni Lambretta 200 casing
Replies: 40
Views: 9823

Re: Uni Lambretta 200 casing

We've had a few delivered to Perth, Western Australia, so they must be available now. On initial perusal they look good quality, like the side casings and mag housings, and I think they have a bigger gasket face around the transfers.
by Minority
Sun Oct 21, 2018 12:23 am
Forum: Lambretta Tech
Topic: Cracked casing
Replies: 43
Views: 5672

Re: Cracked casing

Is it my imagination Gary, or does the mag side silentblock look as though it’s not all the way in?
by Minority
Sat Oct 13, 2018 9:51 am
Forum: Lambretta Tech
Topic: Indian li150 gearbox
Replies: 18
Views: 2004

Re: Indian li150 gearbox

If you used a 14T front sprocket with your TV200 box it would actually have better ratios than the SX200 box. It might make the clutch work a bit harder and it's a bit small for my liking (cush drive surface has to be undercut for the chain I believe). You'd also have to sort out chain length, altho...