do a straight swap with a LI 125 box to give a ratio of 5.00 on the same sprockets
friend runs the same set up and it does 80mph gps speed
Search found 298 matches
- Sun Jun 05, 2011 7:36 pm
- Forum: Lambretta Tech
- Topic: TS1 Ron Moss Ts1
- Replies: 17
- Views: 7639
- Sun Jun 05, 2011 3:18 pm
- Forum: Lambretta Tech
- Topic: Ever seen this before
- Replies: 5
- Views: 2512
Ever seen this before
Been in a couple of years, thought I had holed the piston on the A3M last Monday as bike locked on initial investigation magnet had come loose on the flywheel with what looked like a twisted crank further delving showed the below which probably caused the magnet to come loose 350 rod on sil webs, no...
- Wed May 12, 2010 8:21 pm
- Forum: Lambretta Tech
- Topic: Soppy idea or worth a punt
- Replies: 27
- Views: 10035
Re: Soppy idea or worth a punt
Hi Stevetzr.steve wrote:If that is lockwire on cylinderhead nuts, I would not be tempted to try myself.
yes it is lockwire, can you explain a little more, appreciate your input
- Wed May 12, 2010 7:10 pm
- Forum: Lambretta Tech
- Topic: Soppy idea or worth a punt
- Replies: 27
- Views: 10035
Soppy idea or worth a punt
Work pressure finally easing up
anyway constructive or otherwise comments welcome
anyway constructive or otherwise comments welcome
- Fri Mar 12, 2010 9:53 pm
- Forum: Lambretta Tech
- Topic: dot 5 ?
- Replies: 8
- Views: 2484
Re: dot 5 ?
dot 5.1 is compatible with dot 4
dot 5 is silicone based, really need to clean out the system if changing over to dot 5, easier said than done
dot 5 is silicone based, really need to clean out the system if changing over to dot 5, easier said than done
- Tue Feb 09, 2010 5:47 pm
- Forum: Lambretta Tech
- Topic: Serious Problem With Rear Hub
- Replies: 8
- Views: 4834
Re: Serious Problem With Rear Hub
there is a similiar issue with DRZ400's with the front sprocket always coming loose, very similiar setup to a Lammy with splined layshaft and sprocket, it uses a locking plate to retain the nut once tightened problem is caused by slight wear on the interface between the splines of the sprocket and l...
- Sun Jan 31, 2010 5:55 pm
- Forum: Lambretta Tech
- Topic: £5 Prize to guess top speed on an RT 250
- Replies: 51
- Views: 13534
Re: £5 Prize to guess top speed on an RT 250
Chris CSPE wrote:Give my 5 pounds to help the heroes
Was that you i met at M.B the other day?
No never been to MB,s shop, was at Doncaster for the AGM last week
Darrell is often there thou
- Sun Jan 31, 2010 5:24 pm
- Forum: Lambretta Tech
- Topic: £5 Prize to guess top speed on an RT 250
- Replies: 51
- Views: 13534
Re: £5 Prize to guess top speed on an RT 250
yam-lam wrote:eibargum wrote:Cant be arsed to check , who won.
i think chris cspe with 81mph
Must admit didnt look myself, if Chris cspe pm's me his paypal address, will tfr a fiver
good afternoon out, messing around
- Sun Jan 31, 2010 4:29 pm
- Forum: Lambretta Tech
- Topic: £5 Prize to guess top speed on an RT 250
- Replies: 51
- Views: 13534
Re: £5 Prize to guess top speed on an RT 250
results are in the mad mile is slightly less than 1 Km end to end Rapido 250 32mm VHSA taffy 68mph Race Rapido 225 30mm phbh NK, AF Flywheel 75.8mph TS1 225 35mm TMX, Ancilliotti Clubman Freshly rebuilt 73.9mph Stage 4 200 30mm phbh Clubman 64.7mph RT220 30mm phbh VW Reverse clubman 67mph TS1 225 30...
- Sun Jan 31, 2010 12:02 pm
- Forum: Lambretta Tech
- Topic: £5 Prize to guess top speed on an RT 250
- Replies: 51
- Views: 13534
Re: £5 Prize to guess top speed on an RT 250
yam-lam wrote:83.5 gps road speed ......... what clubman are you using
some one off made between B Race and MB, with a few hours on the dyno
maybe IAN can say more