Search found 315 matches

by nellyboyo
Tue May 21, 2019 8:43 am
Forum: Lambretta Tech
Topic: Lambretta crank induction with Malossi MHR 221
Replies: 16
Views: 522

Re: Lambretta crank induction with Malossi MHR 221

Brilliant effort ...no frame clearance issues ???
by nellyboyo
Sat May 18, 2019 5:07 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

OK tidy , I`ll check
by nellyboyo
Sat May 18, 2019 8:57 am
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

I`m probably a bit late to the party ...but I hadn`t seen these before ??? https://www.jockeys-boxenstop.de/Final-drive-bearing-Jockeys-Boxenstop-Series-1-3-DL-GP Whats the idea ?? 2 shims instead of the old 1 and a dust felt pad under the retaining plate against the bearing ...??? Not that I want t...
by nellyboyo
Sat May 18, 2019 8:40 am
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

Well , I agree , I`m annoyed that a pre-fitted bearing seal appears to be the wrong way around ..thats just ridiculous . I`ll look into getting a new rolf seal and some kind of guide to get the innner sealing lip facing downwards .
by nellyboyo
Fri May 17, 2019 3:32 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

Well, that`ll be about the 4th seal tried ...I used a double lip seal last time on the other MB bearing ....OK , when you fit the seal . does the inner lip sit up or down if that makes sense. I carefully ran my nail around the inner seal to poke it down on one seal , then span the inner race and the...
by nellyboyo
Fri May 17, 2019 12:47 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

Well that's a BGM bearing that came with the seal fitted ??? the spring is facing the gearbox ??
I think that's in correctly ?
Ive taken the mesh out of the oil filler plug so its just straight through ...so should be no pressure build up there
by nellyboyo
Fri May 17, 2019 7:30 am
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

Heres some pics of the leak ......

Image

Image
by nellyboyo
Thu May 16, 2019 12:36 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Re: Wits end ...and past it

ha, no it doesn't seem silly mate ...yes definitely fitted the right way ....I have chucked old bearings ....and yes, my mate mentioned that they were preferable sometimes ...After I had chucked them out :cry:
by nellyboyo
Thu May 16, 2019 11:07 am
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 675

Wits end ...and past it

:oops: Just fettling my TV200 rebuild and , for the life of me , cannot get the rear hub oil seal to stop leaking after a good run ...Its a TV2 casing and appears to be in good nick all round where the bearing sits so I`d obviously want to keep using that .... so far I have systematically replaced ....