Search found 289 matches

by gerryjunior
Sun Sep 15, 2019 8:34 pm
Forum: Lambretta Tech
Topic: Series 3 engine in an LD frame
Replies: 1
Views: 79

Re: Series 3 engine in an LD frame

Image
i used an indian gp frame with and ld rear arch, handling was good enough for a casa ss 225
by gerryjunior
Fri Mar 29, 2019 11:39 pm
Forum: Lambretta Tech
Topic: Weird GP chassis number
Replies: 7
Views: 1011

Re: Weird GP chassis number

ive owned 2 22/4 gps, a 97 and a 98 , both had turning mudguards , both original irish registered from new , both 200's .
by gerryjunior
Fri Feb 22, 2019 11:27 pm
Forum: Lambretta Tech
Topic: Series 1 Wiring /elecrtonic ignition
Replies: 3
Views: 384

Re: Series 1 Wiring /elecrtonic ignition

what regulator are you using , are you using the standard junction box, no need to change the loom , the wire from the lighting coil in the stator (usually yellow) connects beside the brown from the loom this will give power to lights horn etc, green from the loom goes beside green from the stator a...
by gerryjunior
Mon Jun 19, 2017 9:33 pm
Forum: Carburettor Set-ups
Topic: Lambretta Carb Set-ups.....
Replies: 77
Views: 155111

Re: Lambretta Carb Set-ups.....

rapido 250, af 48 mm big bore, gt 60 x 110 crank ,mammoth head, cyclone gearbox, 30 mil phbh, 40 slide, 70 choke, 130 main, av 268, 70 choke . x 13 needle , breath sweet filter.
by gerryjunior
Mon Jun 19, 2017 9:29 pm
Forum: Carburettor Set-ups
Topic: Lambretta Carb Set-ups.....
Replies: 77
Views: 155111

Re: Lambretta Carb Set-ups.....

rapido 225 , 58 mil crank, bgm exhaust v1 30mil phbh, 40 slide, 122 main , 70 choke, 55 pilot ,av 266 x13 needle,
by gerryjunior
Sat Apr 01, 2017 8:16 pm
Forum: Lambretta Tech
Topic: Clearance for 110 x 60 ???
Replies: 7
Views: 1073

Re: Clearance for 110 x 60 ???

I fitted a gran tourismo 60 stroke recently , didn't have to touch the casing ,
by gerryjunior
Mon Mar 27, 2017 11:31 pm
Forum: Lambretta Tech
Topic: Rapido Race 225, jetting
Replies: 8
Views: 1504

Re: Rapido Race 225, jetting

I run mine with an Avanti piston and head, lovely to drive now , it was a right pain to tune with the original piston , the 3mm shortened skirt makes it very difficult to get them to idle,
by gerryjunior
Sun Mar 26, 2017 4:43 pm
Forum: Lambretta Tech
Topic: Rapido Race 225, jetting
Replies: 8
Views: 1504

Re: Rapido Race 225, jetting

mine is 40 slide, 125 main ,70 choke , 55 pilot ,av 266, x7 needle 300 float , hope it helps ,
by gerryjunior
Mon Mar 13, 2017 8:15 pm
Forum: Lambretta Tech
Topic: SIL crank
Replies: 10
Views: 1860

Re: SIL crank

ive seen the big end weld itself on 2 indian cranks , bearings were just bits if wire, I kid you not they blued and heated themselves together, but I must stress neither were bought from an sil dealer , i have an sil 200 that i bought from scooter restorations and in 5 yrs its been very reliable, no...