What jetting did you end up at with the Mikuni?
Cheers
Search found 26 matches
- Sun Jan 12, 2014 10:18 am
- Forum: Lambretta Tech
- Topic: Franspeed super tourer on a TS1?
- Replies: 10
- Views: 7517
- Wed Oct 16, 2013 7:40 pm
- Forum: Lambretta Tech
- Topic: Serveta 200 with a snapped crank, ooops :-(
- Replies: 39
- Views: 12521
Re: Serveta 200 with a snapped crank, ooops :-(
Damn i've just bought one of these cranks.strangely to replace a Mazuchelli one, that's been in the motor for about ten years,that has a ridge worn into the small end eye.I'll have to check the gudgeon pin too.Only a stage 4 MB indian 225 barrel but it's on a GT casing which i'd rather not have to r...
- Thu Oct 03, 2013 2:47 pm
- Forum: Show us yer Scoots!!
- Topic: Gt200 found in garage, one owner and untouched since 1974
- Replies: 27
- Views: 10617
- Tue May 21, 2013 10:45 am
- Forum: Lambretta Tech
- Topic: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test.....
- Replies: 750
- Views: 293712
Re: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test....
Kit no:3 is coming out of hibernation now my GT is kaput 
I'll be putting in an LTH 7 plate today/tommorow as when i last used it there was a bit of slipping when caning.
I'll be putting in an LTH 7 plate today/tommorow as when i last used it there was a bit of slipping when caning.- Sun May 12, 2013 10:10 am
- Forum: Lambretta Tech
- Topic: Rayspeed race clutch
- Replies: 33
- Views: 12392
Re: Rayspeed race clutch
For fit and forget, I've yet to find or use a better complete clutch package than the LTH 7 plate.[/quote] I'll second that.I've got one in a tv200 (225 stg4) and i've done over 10,000 miles on the same plates.I took them out to check 2 weeks ago and there was 0.07mm wear across the 7 corks against ...
- Tue Apr 16, 2013 4:08 pm
- Forum: Lambretta Tech
- Topic: Mikuni fitting with out cutting the floor
- Replies: 4
- Views: 1984
Re: Mikuni fitting with out cutting the floor
I've not tried to fit the rear runner yet but i've already found the carb top hits the toolbox and brass fuel feed pipe will be rubbing against the engine mount when i fit the fuel line. :x If i'd known it was gonna be this much hassle i'd have left the Amal on there.I've got an old broady manifold/...
- Wed Dec 19, 2012 3:40 pm
- Forum: Lambretta Tech
- Topic: TV200 frame
- Replies: 13
- Views: 6976
Re: TV200 frame
Unless the frame has the factory model and frame number then it's a series 3 type frame and worth less in reality than a factory stamped Li 125 frame.Dressing it up as a GT makes it no more a GT than a P range.It never left Croydon as a GT so what makes it one 50 years later? :freak: Apart from some...
- Thu Nov 29, 2012 5:03 pm
- Forum: Lambretta Tech
- Topic: 12v conversion.
- Replies: 16
- Views: 5119
Re: 12v conversion.
Indian? sorry you've lost me 
- Thu Nov 29, 2012 10:28 am
- Forum: Lambretta Tech
- Topic: 12v conversion.
- Replies: 16
- Views: 5119
Re: 12v conversion.
That's by wun hung lo.
- Wed Nov 28, 2012 5:03 pm
- Forum: Lambretta Tech
- Topic: 10W/40 OIL
- Replies: 2
- Views: 1622
Re: 10W/40 OIL
Had no problems with mine. :bigsm: