Search found 45 matches
- Tue May 22, 2018 7:20 pm
- Forum: Lambretta Tech
- Topic: Master cylinder
- Replies: 0
- Views: 2133
Master cylinder
Have had problems with my mission master cylinder leaking...all over the paintwork...FFS. looking to replace it with a remote reservoir type. Any recommendations
- Thu Sep 28, 2017 11:15 am
- Forum: Vespa Tech
- Topic: PX200 tuning
- Replies: 24
- Views: 13031
PX200 tuning
Can anyone point me in the right direction, got a PX200 engine to play with. I remember an article in scootering about a tune by Harry Barlow on these where the barrel was measured and then topped or tailed to bring it into spec. If anyone can send me the magazine number or even better a copy of the...
- Fri Aug 04, 2017 8:11 pm
- Forum: Vespa Tech
- Topic: PX 200 and PM evolution pipe
- Replies: 1
- Views: 2178
PX 200 and PM evolution pipe
Any suggestions for the jet sizes for a standard PX200 and a PM Evolution pipe? All standard with the exception of the pipe - gotta start somewhere. Thank in advance
- Wed Aug 02, 2017 11:46 am
- Forum: Vespa Tech
- Topic: Vespa stand
- Replies: 2
- Views: 2836
Re: Vespa stand
Cheers, all sorted now - dreamless you've gotta love em
- Tue Aug 01, 2017 3:19 pm
- Forum: Vespa Tech
- Topic: Vespa stand
- Replies: 2
- Views: 2836
Vespa stand
Just fitted a new PM exhaust to the P2, everything fits well. Went to take the scooter off it's stand and found the exhaust stops the sta d from going up. The bit where the spring attaches to the stand fouls on the exhaust. Any recommended ways of getting round this. I can cut the stand, but where d...
- Sat Apr 08, 2017 8:17 am
- Forum: Paint & Bodywork Tech
- Topic: GP side panel crack repairs
- Replies: 3
- Views: 3458
Re: GP side panel crack repairs
I live in Belfast area, not a lot of auto retorers over here.
- Tue Apr 04, 2017 11:24 am
- Forum: Paint & Bodywork Tech
- Topic: GP side panel crack repairs
- Replies: 3
- Views: 3458
GP side panel crack repairs
Can anyone recommend someone who would be able to sort out my panels for me. Cracks in the usual places at the bottom of both panels and also where my carb has been rubbing on the inside of the RH panel. Original panels so don't want to cut holes or trim them up. Thanx in advance
- Fri Aug 14, 2015 8:14 am
- Forum: Sports Bar
- Topic: The Song Title Thread - Pointless but Addictive!
- Replies: 26185
- Views: 5536892
Re: The Song Title Thread - Pointless but Addictive!
Dream time - The cult
- Thu Jun 18, 2015 11:23 pm
- Forum: Lambretta Tech
- Topic: Piston crown level?
- Replies: 4
- Views: 2434
Re: Piston crown level?
Removed the cylinder head and one of the studs winds out, no probs me thinks. Stud winds out, but sticks, pull the cylinder off and low and behold there's a poxy thread repair been carried out at some point, which has now decided to let go. Where or who does timeserts? I have the capability to carry...
- Thu Jun 18, 2015 5:18 pm
- Forum: Lambretta Tech
- Topic: Piston crown level?
- Replies: 4
- Views: 2434
Re: Piston crown level?
Standard sized crank and rod, TS1 in standard form, Indian casings.