Search found 60 matches
- Sun Apr 06, 2014 3:48 pm
- Forum: Lambretta Tech
- Topic: What's the latest on cyclone 5 boxes?
- Replies: 7
- Views: 2779
Re: What's the latest on cyclone 5 boxes?
AF Rayspeed had some in stock last week mate...
- Sun Apr 06, 2014 3:41 pm
- Forum: Lambretta Tech
- Topic: Targa Damper Fitment
- Replies: 11
- Views: 4215
Re: Targa Damper Fitment
Mine are fitted with a PM double disc,so the fork links are swapped ,which means welding a place for the damper to bolt to.At the top the damper is mounted to the outside of the bracket.i used a nylon spacer inside the bracket and a long bolt through the lot.Works well for me.Hope this helps Tom I ...
- Sat Dec 14, 2013 8:11 am
- Forum: Lambretta Tech
- Topic: Jumpiung out of 2nd gear
- Replies: 7
- Views: 4065
Re: Jumpiung out of 2nd gear
could be badly adjusted cables or worst case worn sliding dog or second gear sounds serious but not a big job plenty of good advice and knowledgeable guys on here that will keep you right Agree jumping in second sounds like your gear selectors worn..have a read of stickys book if your not sure also...
- Thu Dec 05, 2013 5:03 pm
- Forum: Lambretta Tech
- Topic: Jockey Boxenstop rear brake
- Replies: 9
- Views: 5490
Re: Jockey Boxenstop rear brake
same here mine came with both cams...good bit of kit thoughwurzel wrote:Mine came with two different cams one for the Li and one for the GP
- Sun Dec 01, 2013 6:31 pm
- Forum: Lambretta Tech
- Topic: RS 225 Ralph saxelby
- Replies: 22
- Views: 11162
Re: RS 225 Ralph saxelby
the piston you have looks like a Suzuki ts250 word of warning mate don't buy any patern piston or rings off e.pay they are made of cheese,you may also need some spacers for your gudgeon pin
- Sat Nov 30, 2013 7:11 pm
- Forum: Lambretta Tech
- Topic: CYCLONE GEARBOX – BATCH 2 RECALL
- Replies: 104
- Views: 32370
Re: CYCLONE GEARBOX – BATCH 2 RECALL
more than happy with mine ran a tuned ts1 high bhp franspeed race pipe, the cyclone gearbox performed well (always a revvy monster) always had the edge on pick up and had the power on inclines ,dropped a ring peg and I found a crack on the spigot of the barrel from a repair...just had a cast iron rs...
- Sun Nov 03, 2013 7:09 pm
- Forum: Lambretta Tech
- Topic: Gear selector question (Cyclone5 releted)
- Replies: 2
- Views: 1466
Re: Gear selector question (Cyclone5 releted)
agree with vespanic make sure you are able to locate 1st and 5th gear,a tip I would use is when you fit the box jack your back wheel off the ground spin your wheel and check if you can get all gears by moving your gear arm,then leave in 5th and make sure your tie bar can move far enough back to slot...
- Thu Sep 12, 2013 6:30 pm
- Forum: Show us yer Scoots!!
- Topic: My works Super Monza DTC rosa bianca by maca
- Replies: 34
- Views: 13644
Re: My works Super Monza DTC rosa bianca by maca
very nice mate, remember seeing one of the first ones painted in the spray booth when dtc were under the arch,s in leeds must have been 84,85
- Thu Aug 22, 2013 4:37 pm
- Forum: Lambretta Tech
- Topic: Cyclone 5 Speed
- Replies: 12
- Views: 4797
Re: Cyclone 5 Speed
I have one in my ts1 now set up runs ok no problem over 25bhp (glad I fitted a standard gear selector spring) any problems rlc happy to help out
- Fri Jul 19, 2013 6:49 am
- Forum: Lambretta Tech
- Topic: New Cyclone Xmas tree
- Replies: 34
- Views: 10046
Re: New Cyclone Xmas tree
Stupid question, but obviously you did refit the 5-speed selector when you swapped gearboxes from 4-speed back to 5-speed didn't you? If it jumps out of 5th then there are a few things to check: * if the rubber cover on the tie rod is touching the rear shock casting * if the nearest rubber cable ga...