Search found 37 matches
- Sat Jul 08, 2017 9:33 am
- Forum: Lambretta Tech
- Topic: Anyone had a replate at Langcourts recently?
- Replies: 3
- Views: 2714
Re: Anyone had a replate at Langcourts recently?
Just had a TS1 done £147 that's with vat and postage.
- Tue Aug 09, 2016 4:41 pm
- Forum: General Scooter Chat
- Topic: KMT products
- Replies: 6
- Views: 4051
KMT products
Just received a box of 10 push in main jets for the Vespa from KMT for £9.80 that's including postage. I've got to say they look very good quality and value for money as some dealers are selling these at over £6 per jet. Going to have a play about with jetting tonight and see what there like.
- Thu Mar 31, 2016 8:38 pm
- Forum: Lambretta Tech
- Topic: Sip valves
- Replies: 2
- Views: 1719
Re: Sip valves
Ah ok many thanks I will have a look 
- Thu Mar 31, 2016 8:21 pm
- Forum: Lambretta Tech
- Topic: Sip valves
- Replies: 2
- Views: 1719
Sip valves
Anybody know the thread size do sip valves? I have snapped one in the rim and it needs re tapping. I've used a thread gauge on it and it's a m8 x 0.8 which is a unusual size has anybody had to do this before?
- Sun Jan 03, 2016 7:51 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
Re: Vespa Inlet Porting
Ok Sean many thanks for the advice much appreciated.
- Sun Jan 03, 2016 6:18 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
Re: Vespa Inlet Porting
Thanks Sean, I was just going to remove 4mm from the rear as per instruction but I will have a go the way you suggested to make sure it's right.
Do you open all of the inlet or taper it down leaving the top of inlet hole the same size?
Do you open all of the inlet or taper it down leaving the top of inlet hole the same size?
- Sun Jan 03, 2016 5:11 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
Re: Vespa Inlet Porting
Not sure if that last link worked either but here it is again if anyone can help ta.
https://www.flickr.com/photos/138247792@N08/sh
https://www.flickr.com/photos/138247792@N08/sh
- Sat Jan 02, 2016 8:46 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
Re: Vespa Inlet Porting
Cheers Norrie I'll have a look.
- Sat Jan 02, 2016 7:31 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
- Sat Jan 02, 2016 12:40 pm
- Forum: Vespa Tech
- Topic: Vespa Inlet Porting
- Replies: 8
- Views: 5159
Vespa Inlet Porting
I've got my hands on a Polini 210 with Polini 60mm crank and have just matched the casings to the barrel. I now need to modify the carb inlet, looking at the supplied instructions it looks as though you have to elongate it by 4mm. My question is do you do this at the back end of the port the furthes...