Search found 33 matches
- Tue Oct 05, 2010 6:14 pm
- Forum: Tech FAQ
- Topic: how du u bleed disc brake ?
- Replies: 31
- Views: 10998
Re: how du u bleed disc brake ?
After many frustrating hours with this problem, i was lent an industrial vacum pump as used in garages which works instantly. My garage friend assured me you can get 'budget' versions which are more than ample for our purposes! i found this on on ebay and it works a treat, fully bled front caliper i...
- Wed Sep 22, 2010 6:25 pm
- Forum: Lambretta Tech
- Topic: Box pipes + reed valves
- Replies: 6
- Views: 2637
Box pipes + reed valves
Does anyon run the combination of the new Ancilotti box pipe with a reed valve cylinder (Imola/TS1/monza), apart from the obvious drop in top performance of an expansion does the balance of extra low end torque vs top revs effectively work? Basically i have finished the rebuild after being cleared u...
- Sat Aug 28, 2010 1:12 pm
- Forum: Lambretta Tech
- Topic: GP Wiring
- Replies: 1
- Views: 1263
GP Wiring
Just finished the rebuild after getting knocked off and after starting the scoot was checking the wiring and lights etc... all works as it should however with the key in position 3 (main lights) everything works as it should however when you flick the onto main beam both the headlight and pilot ligh...
- Fri Jul 30, 2010 4:42 pm
- Forum: Lambretta Tech
- Topic: Centre stand fitting
- Replies: 2
- Views: 2133
Centre stand fitting
Just started putting the scoot back together, does the stand u bracket fit to the front or rear of the crossmember? there isn't a pic in stickys book!
Cheers
Cheers
- Sun Jul 25, 2010 6:25 pm
- Forum: Lambretta Tech
- Topic: GP Ignition switch
- Replies: 2
- Views: 1682
Re: GP Ignition switch
Excellent, many thanks!
- Sun Jul 25, 2010 3:03 pm
- Forum: Lambretta Tech
- Topic: GP Ignition switch
- Replies: 2
- Views: 1682
GP Ignition switch
Just replacing the loom, switches etc... and whilst the majority is a striaghtforward colour to colour can anyone advise what the blue wire is from the igintion switch
This is an electronic loom (non battery)
Thanks
This is an electronic loom (non battery)
Thanks
- Mon May 03, 2010 3:07 pm
- Forum: Lambretta Tech
- Topic: Clutch 'free play'
- Replies: 11
- Views: 5095
Re: Clutch 'free play'
if you take it apart again you´ll probably find that the ears of the bottom steel plate catch against the flanks of the pressure plate. if you pull in the clutch it will not have enough free play since that steel plate rests on the flanks of the pressure plate. file down the lugs (every second one...
- Sun May 02, 2010 9:23 pm
- Forum: Lambretta Tech
- Topic: Clutch 'free play'
- Replies: 11
- Views: 5095
Re: Clutch 'free play'
Hi Sean,sean brady scooters wrote:did you check the heights between center shoulder of spider and clutch bell housing..
If i understand you correctly, the pressure plate sits below below the spider by a few mill and bottoms out on the crownwheel?
- Sun May 02, 2010 8:32 pm
- Forum: Lambretta Tech
- Topic: Clutch 'free play'
- Replies: 11
- Views: 5095
Re: Clutch 'free play'
Hi,
Yes, complete 5 plate kit, also have the yamaha lever and friction free cable?
Yes, complete 5 plate kit, also have the yamaha lever and friction free cable?
- Sun May 02, 2010 4:04 pm
- Forum: Lambretta Tech
- Topic: Clutch 'free play'
- Replies: 11
- Views: 5095
Clutch 'free play'
I am replacing the clutch for the new MB kit (billet spider and new pressure plate) and on the first go it drags terribly to the point of not being able to slect gears without stalling, when compressed the plates have aprx 1.5mm of free play, is this ok? I can get the scoot to select a gear but this...