Search found 32 matches

by netweasel
Thu Apr 06, 2017 12:38 am
Forum: Lambretta Tech
Topic: Exhaust joint sealant
Replies: 9
Views: 4040

Re: Exhaust joint sealant

Permatex 81878 Ultra Copper, or Loctite 5920. I also use these for almost every under-pressure gasket on the engine. Get some gloves on, and add a bead of sealant to the gasket faces, then run your fingers over the gasket and smooth it all out leaving a nice goldilocks (not too thin, not too thick) ...
by netweasel
Tue Jun 09, 2015 3:40 am
Forum: Carburettor Set-ups
Topic: BGM PWK 28 idle behaviour
Replies: 10
Views: 8550

Re: BGM PWK 28 idle behaviour

Here is a PWK how-to I posted on the LCUSA forum: I recently picked up a GP200 that had a OKO/PWK 30mm fitted with an old PM Style ScootRS pipe. Although it ran, it was jetted poorly, not to mention that whoever last rebuilt the carb stripped most of the housing and jet threads. So I picked up a few...
by netweasel
Wed Oct 22, 2014 6:28 pm
Forum: Lambretta Tech
Topic: Sidecar gearing
Replies: 11
Views: 4283

Re: Sidecar gearing

I built up a Jet200 sidecar rig with a metal Cozy sidecar. I used Li150 gearing, and it pulled great through all the gears.
Image
by netweasel
Thu Oct 09, 2014 7:58 pm
Forum: Lambretta Tech
Topic: Zaurst fitment problems
Replies: 1
Views: 1424

Re: Zaurst fitment problems

If your exhaust is touching the chaincase, this has to do with the front and rear mounts not the u-bend. You can add some flat washers behind the front and rear exhaust bracket until it is space out enough from the chaincase. Depending on how far you need to space it out, you might need to get some ...
by netweasel
Wed Oct 08, 2014 6:48 pm
Forum: Lambretta Tech
Topic: Stripped thread
Replies: 6
Views: 3409

Re: Stripped thread

are you on commission? I've used jubilee clips to bodge an encoder together once, so one could equally say "jubilee clips are professional offshore construction industry quality and used in the marine industry". I'm not saying they aren't better than helicoils, just wondering if you're a ...
by netweasel
Wed Oct 08, 2014 2:44 am
Forum: Lambretta Tech
Topic: Stripped thread
Replies: 6
Views: 3409

Re: Stripped thread

M6 Time-Sert. The kit isn't cheap, but you can also use the M6 for stripped case studs. I use it on all M6 case studs that have an exhaust mount attached to it. Unlike Helicoil, Time-Serts have a collar that prevents the insert from going in too far. Time-Serts are professional aircraft quality, and...
by netweasel
Wed Oct 08, 2014 12:03 am
Forum: Lambretta Tech
Topic: AF CASSETTE CLUTCH PROBLEMS.
Replies: 15
Views: 10072

Re: AF CASSETTE CLUTCH PROBLEMS.

I have installed a few SSC clutches, they are great. They take some setting up though, if it slipped it is because it was constantly disengaged. You need to shave off some of the brass plunger.
by netweasel
Tue Oct 07, 2014 2:34 am
Forum: Lambretta Tech
Topic: Lambretta mag housing nightmare, all help appreciated !
Replies: 18
Views: 7987

Re: Lambretta mag housing nightmare, all help appreciated !

What would I do? I would tap a few new M6 holes, or use M6 Time-Sert inserts in the old stripped holes, then use this tool to remove the mag flange: http://jet200.com/catalog/product_info.php?products_id=1572 http://jet200.com/catalog/images/1572.jpg Heating the actual case around where the mag-flan...
by netweasel
Tue Jun 17, 2014 10:57 pm
Forum: Lambretta Tech
Topic: Jockey Boxenstop rear brake problem
Replies: 16
Views: 6751

Re: Jockey Boxenstop rear brake problem

I've got a stand like that but it goes nowhere near the tyre. If you insert them properly from the inside out, they can. If you insert it from the cover side, it will not. Since mine is set up, I was thinking of tack welding the pivot post to the plate while it is on the scooter, then dissembling i...
by netweasel
Tue Jun 17, 2014 5:11 pm
Forum: Lambretta Tech
Topic: Jockey Boxenstop rear brake problem
Replies: 16
Views: 6751

Re: Jockey Boxenstop rear brake problem

ill dedicate a full day to this on sunday and up date, just seems weird that the hub should go on sweet with clearance then only bind when tighten down........ It is not weird if you think about what I just explained. Before you tightened the rear hub nut, it spun freely, yes? When you tighten down...