Search found 90 matches
- Tue Jun 09, 2015 3:52 pm
- Forum: Lambretta Tech
- Topic: First ride - heavy clutch
- Replies: 22
- Views: 9986
Re: First ride - heavy clutch
If you look at a worn clutch most the time the tabs on the lower plates show more wear than the top ones, I've always put it down to being more stress at that area.
- Tue Jun 09, 2015 3:44 pm
- Forum: Lambretta Tech
- Topic: Timing Strobe
- Replies: 7
- Views: 3689
Re: Timing Strobe
connecting it to any 12v battery is fine.
I read the bit above as don't use the ones that connect in-line or the ones that use Built in batterys
I read the bit above as don't use the ones that connect in-line or the ones that use Built in batterys
- Wed May 27, 2015 11:37 pm
- Forum: Lambretta Tech
- Topic: Earth Fault?
- Replies: 18
- Views: 5637
Re: Earth Fault?
Check your HT lead it might be shorting out on the frame or engine. I had the same on a gp, it would cut out occasionally but always restart, then it started happening every time I took of the stand after checking everything I noticed that when it was off the stand the HT lead was arching out on the...
- Fri Mar 13, 2015 9:03 pm
- Forum: Lambretta Tech
- Topic: SIP Wheel nuts
- Replies: 6
- Views: 2898
Re: SIP Wheel nuts
The nuts that come with the SIP rims are shite and rust almost straight away and I've had a few with weak threads, the Mb ones look and last a lot better
- Fri Mar 13, 2015 8:00 pm
- Forum: Lambretta Tech
- Topic: SIP Wheel nuts
- Replies: 6
- Views: 2898
Re: SIP Wheel nuts
Not sure about chrome, but you can get the Stainless steel ones from Mb.
- Tue Feb 10, 2015 12:19 am
- Forum: General Scooter Chat
- Topic: genuine piaggio LT coils ?
- Replies: 2
- Views: 2422
Re: genuine piaggio LT coils ?
Your best bet would be Fowlers of Bristol, always found they've had good stock
- Sun May 18, 2014 11:40 pm
- Forum: Lambretta Tech
- Topic: Scootrs outboard disc EBC pads?
- Replies: 11
- Views: 5115
Re: Scootrs outboard disc EBC pads?
I think it's FA092
- Sun May 04, 2014 12:29 am
- Forum: Lambretta Tech
- Topic: Newfren Clutch Plates
- Replies: 3
- Views: 2267
Re: Newfren Clutch Plates
All steels used were flat, went through a few to get perfect ones, a fraction over 18mm can't remember exactly off the top of my head (brains not what it used to be) :oops: There was plenty of clearance, MB springs same as I always use, I've used less clearance before on other clutches without probl...
- Sat May 03, 2014 11:26 pm
- Forum: Lambretta Tech
- Topic: Newfren Clutch Plates
- Replies: 3
- Views: 2267
Re: Newfren Clutch Plates
Nobody else using them or had probs? Soaked a new set for 36 hours fitted them 1.8 clearance between the plates, 2mm at the lever, tested fine when cold outside the workshop, mates picks it up all fine after a bit of a run starts to drag again, he tried adjusting the cable almost to the point of not...
- Wed Apr 30, 2014 10:48 pm
- Forum: Lambretta Tech
- Topic: Newfren Clutch Plates
- Replies: 3
- Views: 2267
Newfren Clutch Plates
Anyone had any problems with Newfren clutch plates? Had one at the weekend only done a few miles and it started to drag badly, tried adjusting the cable still the same, striped it down and the plates are burnt, checked the clearance and it's just over 1mm, when built it was just under 2mm. Plates we...