Very impressive.
I was only thinking the other day why don't more people use taper bearings when scratch building a scoot.
Can't wait for more posts.
Search found 614 matches
- Mon Aug 12, 2013 10:33 am
- Forum: Show us yer Scoots!!
- Topic: my first ever scooter build. cagiva mito 125 engine
- Replies: 160
- Views: 59896
- Mon Jun 03, 2013 9:26 pm
- Forum: Vespa Tech
- Topic: rotary valve inlet timing on PE /PX range vespas
- Replies: 19
- Views: 13235
Re: rotary valve inlet timing on PE /PX range vespas
I've got it all written down somewhere Sean. I'll try and remember to dig it out and let you know.
Dan yes I have thought of using M-tech but keep selling them to dyno customers before I get a chance!
Dan yes I have thought of using M-tech but keep selling them to dyno customers before I get a chance!
- Sun Jun 02, 2013 4:52 pm
- Forum: Vespa Tech
- Topic: rotary valve inlet timing on PE /PX range vespas
- Replies: 19
- Views: 13235
Re: rotary valve inlet timing on PE /PX range vespas
I ported my own Polini this way and it seems to do what the theory suggests which is increase bottom to mid range power with little in the way of over rev. This is because I knew the exhaust timing would be relatively low and also I wanted to pull taller gearing. It does 70mph at 6500rpm and has don...
- Sun Jun 02, 2013 2:07 pm
- Forum: Lambretta Tech
- Topic: CYCLONE GEARBOX – BATCH 2 RECALL
- Replies: 104
- Views: 32337
Re: CYCLONE GEARBOX – BATCH 2 RECALL
Sydducket if you paid cash to Stuart for the box it may be why Dean hasn't got your details. You also won't have heard from him if your gearbox is from the first batch as there is no issue with those.
If you send me your details I'll happily get Dean to ring you.
If you send me your details I'll happily get Dean to ring you.
- Sun Jun 02, 2013 2:00 pm
- Forum: Show us yer Scoots!!
- Topic: Lambretta cutdown finally finished
- Replies: 14
- Views: 13000
Re: Lambretta cutdown finally finished
Supercool love that
- Fri May 31, 2013 9:00 pm
- Forum: Lambretta Tech
- Topic: CYCLONE GEARBOX – BATCH 2 RECALL
- Replies: 104
- Views: 32337
Re: CYCLONE GEARBOX – BATCH 2 RECALL
I am the only other dealer allowed to buy direct from RLC other than Stuart Owen so know some of the details behind this. The spec of the interference fit was changed without Deans knowledge but with the best intentions of improvement by DRT. It didn't work it was a cock up and they have dealt with ...
- Mon Apr 29, 2013 9:10 am
- Forum: Lambretta Tech
- Topic: TS1 flat spot remedy
- Replies: 9
- Views: 3833
Re: TS1 flat spot remedy
Try it with a 50 slide Paul. You may need to up the pilot slightly.
- Wed Apr 03, 2013 1:37 am
- Forum: Lambretta Tech
- Topic: Small block tuning or bite the bullet?
- Replies: 14
- Views: 9109
Re: Small block tuning or bite the bullet?
You can get TS1 power from a small block but it will be at higher revs. This doesn't mean you can't tour on a small block motor though. The GT,Muggy and certainly a well tuned cast barrel are all capable of touring you just have to be realistic about what your mile-munching speed will be. A well set...
- Wed Mar 27, 2013 10:40 am
- Forum: Show us yer Scoots!!
- Topic: MADSPEED PERFORMANCE LAMBRETTA TUNING S2 No31
- Replies: 143
- Views: 67652
Re: MADSPEED PERFORMANCE LAMBRETTA TUNING S2 No31
Great work. Must admit I didn't get the paint untill the pinstriping but its a great look. Have to agree about using original parts. Saves workshop time in the end because they fit and actually work. I went to clear a garage of an old mate some months ago and could have cried when I asked what happe...
- Sun Feb 24, 2013 2:54 pm
- Forum: Show us yer Scoots!!
- Topic: Maicoletta
- Replies: 6
- Views: 4711
Re: Maicoletta
Absolutely gorgeous!