Search found 614 matches
- Sun Jun 14, 2009 10:41 pm
- Forum: Lambretta Tech
- Topic: The end of the Lambretta crank as we know it ???
- Replies: 179
- Views: 41586
Re: The end of the Lambretta crank as we know it ???
For me the Vespa is a bad example to use in the case for LPC because I think the gains come from getting the gas past the crank and not being obstructed by it rather than lowering primary compresion or rotating mass. I do agree about vibration though Sean as Harry does ones for me very similar to yo...
- Sun Jun 14, 2009 10:06 pm
- Forum: Lambretta Tech
- Topic: RB20 reports
- Replies: 38
- Views: 7393
Re: RB20 reports
Baz was the guy measuring your rpm? If he didn't you won't get a reliable torque figure anyway. I absolutely garuntee that RB20s make more than 8ft/lb torque
- Sun Jun 14, 2009 10:00 pm
- Forum: Lambretta Tech
- Topic: TS1 crank______Which Yamaha RD conrod?
- Replies: 20
- Views: 5984
Re: TS1 crank______Which Yamaha RD conrod?
Its been a while since I bought one but I think the rd400 has a 115 rod and the RD250 and 350s have 110. The thing is that I think only the 250 one comes with a pin. You'll be able to tell because one will seem a lot cheaper than the other. Marks right about Grampian request their catolougue for all...
- Thu Jun 04, 2009 2:06 am
- Forum: Show us yer Scoots!!
- Topic: Just finishing this off for EuroLambretta...
- Replies: 8
- Views: 2772
Re: Just finishing this off for EuroLambretta...
Very nice Hope all goes well for your journey over. Very pleased because I've got a set of Spanish forks with dampers to go in the LI cut down I have. I knew they worked well but didn't know they could be made to look so good
- Thu Jun 04, 2009 1:22 am
- Forum: Show us yer Scoots!!
- Topic: finally going for it
- Replies: 24
- Views: 6325
Re: finally going for it
If you don't do it you'll always ask yourself what if. Your work speaks for itself. If your venture fails so what-you get another job :) Its difficult making a living out of something which is a huge part of your personel life and its easy to undersell yourself especially to mates or to establish yo...
- Tue Jun 02, 2009 8:25 pm
- Forum: Show us yer Scoots!!
- Topic: Dead RB kit
- Replies: 31
- Views: 8437
Re: Dead RB kit
I take on board what people are saying about the design of the kit but the kit design hasn't caused this. The exhaust has come loose which has almost certainly damaged the gasket. This has caused the motor to run hot and seize. This isn't just any old seize its a total meltdown and I'd bet my mortga...
- Mon Jun 01, 2009 2:49 pm
- Forum: Lambretta Tech
- Topic: Reet
- Replies: 14
- Views: 5151
Re: Reet
Funnily enough the JL4 does produce a lot of torque on big bore motors and tends to behave a little differently than when you put one on say a 225. On a 240 with port timings of 130 trans and 185 exhaust a JL4 gave a 2hp peak horsepower gain and allowed the bike to rev on with useable power for anot...
- Mon May 25, 2009 6:32 pm
- Forum: Show us yer Scoots!!
- Topic: Dead RB kit
- Replies: 31
- Views: 8437
Re: Dead RB kit
Bit of wet and dry and elbow grease will soon sort that
- Mon May 25, 2009 11:17 am
- Forum: Show us yer Scoots!!
- Topic: Scooters at Kelso
- Replies: 4
- Views: 2432
Re: Scooters at Kelso
Great pics-nice to see some well sorted vespas. Yours and your mates are very tasty.
Love the orange 50 spesh as well
Love the orange 50 spesh as well
- Thu May 21, 2009 6:10 pm
- Forum: Show us yer Scoots!!
- Topic: anima mundi 2009
- Replies: 37
- Views: 10380
Re: anima mundi 2009
I think Mark Ryden is brilliant for the same reason I used to like The Beautiful South. The cutesy extreria has a very dark underside.
Scooters that shock especially the public are way overdue a comeback. The edgier the better for me.
Scooters that shock especially the public are way overdue a comeback. The edgier the better for me.