Search found 13 matches
- Thu Apr 11, 2013 10:00 pm
- Forum: Lambretta Tech
- Topic: bgm/mb clubman exhaust
- Replies: 88
- Views: 47182
Re: bgm/mb clubman exhaust
What size is the tailpipe on the new MB Clubman?
- Mon Apr 01, 2013 7:37 pm
- Forum: Lambretta Tech
- Topic: Advice on using choke to stop heat seize on long ride
- Replies: 26
- Views: 9994
Re: Advice on using choke to stop heat seize on long ride
Which type of gauge would people recommend for a basic indication of an engines running temperature?
Cylinder head temperature or exhaust gas temperature?
Thanks
Cylinder head temperature or exhaust gas temperature?
Thanks
- Thu Jan 17, 2013 8:52 pm
- Forum: Lambretta Tech
- Topic: pattern development software
- Replies: 1
- Views: 1384
- Sat Jan 12, 2013 9:25 pm
- Forum: Lambretta Tech
- Topic: Standard stainless exhaust
- Replies: 23
- Views: 6244
Re: Standard stainless exhaust
There is an original drawing of a standard exhaust on the Tutto Lambretta website:
http://www.tuttolambretta.it/galleria.a ... =214&pag=1
Hope this helps.
http://www.tuttolambretta.it/galleria.a ... =214&pag=1
Hope this helps.
- Tue Oct 06, 2009 9:06 pm
- Forum: Lambretta Tech
- Topic: Porting tools....???
- Replies: 30
- Views: 12920
Re: Porting tools....???
You can also get a 3mm collet for the Snap On/Bluepoint right angle grinder.
The part number is: AT1070RA19 and they are £8.40+vat.
I emailed Snap On and asked the question as most of my Burrs/Stones have a 3mm shank.
Does this tool have any kind of speed control?
The part number is: AT1070RA19 and they are £8.40+vat.
I emailed Snap On and asked the question as most of my Burrs/Stones have a 3mm shank.
Does this tool have any kind of speed control?
- Sat Sep 05, 2009 10:41 am
- Forum: Lambretta Tech
- Topic: air fuel ratio....again
- Replies: 6
- Views: 1966
Re: air fuel ratio....again
Taken from A.Bell's book: Ratio of Fuel:Air Starting 1:1-3 Idling 1:8-10 Low speed running 1:10-13 Light load ordinary running 1:14-16 Heavy load running 1:12-14 In the text he states that the required mixture is around 1:12 or 1:13 which is just right for WOT.
- Sat Jun 06, 2009 10:18 pm
- Forum: Lambretta Tech
- Topic: Headset top threads stripped.
- Replies: 5
- Views: 2539
Re: Headset top threads stripped.
It took a while to find, no one had replied when i started searching!
- Sat Jun 06, 2009 8:48 pm
- Forum: Lambretta Tech
- Topic: Headset top threads stripped.
- Replies: 5
- Views: 2539
- Sun May 17, 2009 8:35 pm
- Forum: Lambretta Tech
- Topic: Mikuni TM 28mm Carbs off TZR..??
- Replies: 2
- Views: 2637
Re: Mikuni TM 28mm Carbs off TZR..??
Jamesp from the LCGB forum has quite a bit of experience using these carbs, he put together the following guide to converting and using them on a lambretta: http://members.value.com.au/jamesp/tm28instructions.doc I have a TM28 i am planning to use in the near future, James suggested the following je...
- Fri Apr 10, 2009 7:56 pm
- Forum: Lambretta Tech
- Topic: Clinder head gasket sealent
- Replies: 13
- Views: 4572
Re: Clinder head gasket sealent
Stag Wellseal is good.